M29W160ET-70N6

产品概述

IC Picture

图片仅供参考

制造商IC编号 M29W160ET-70N6
厂牌 MICRON/美光
IC 类别 FLASH-NOR
IC代码 29LV160 TOP
共通IC编号 M29W160ET-70N6 X
M29W160ET-70N6E
M29W160ET-70N6E(ONE LOT)
M29W160ET-70N6EROHS
M29W160ET-70N6F
M29W160ET-70N6H
M29W160ET-70N6T
M29W160ET70N6
M29W160ET70N6-L
M29W160ET70N6E
M29W160ET70N6E (PB FREE)
M29W160ET70N6E IC
M29W160ET70N6E(LF)
M29W160ET70N6E-311B172
M29W160ET70N6E/F
M29W160ET70N6E/NUMONYX
M29W160ET70N6ELEADFREE
M29W160ET70N6ER
M29W160ET70N6F TR
M29W160ET70N6F/E
M29W160ET70N6FLEADFREE
M29W160ET70N6FT
M29W160ET70N6FTSOP48T R
M29W160ET70N6FZ
M29W160ET70N6ST
M29W160ET70N6T7

产品详情

脚位/封装 TSOP-48
外包装
无铅/环保 含铅
电压(伏) 3.3 V
温度规格 -40 C~+85 C
速度 70 NS
标准包装数量
标准外箱
Density 16M
Silicon Version E
Functionality Security Top boot (top blocks protected)
Package TSOP(NA = 48-pin ,12 x 20mm and NB = 56-pin,14 x 20mm)

General Description The M29W160ET/B (2Mb x8 or 1Mb x16) is a nonvolatile device that can be read, erased and reprogrammed. These operations can be performed using a single low voltage (2.7– 3.6V) supply. On power-up the memory defaults to read mode where it can be read in the same way as a ROM or EPROM. The device is divided into blocks that can be erased independently to preserve valid data while old data is erased. Each block can be protected independently to prevent accidental PROGRAM or ERASE commands from modifying the memory. PROGRAM and ERASE commands are written to the command interface of the memory. An on-chip program/erase controller simplifies the process of programming or erasing the memory by taking care of all of the special operations that are required to update the memory contents. The end of a PROGRAM or ERASE operation can be detected and any error conditions identified. The command set required to control the memory is consistent with JEDEC standards. The blocks in the memory are asymmetrically arranged. The first or last 64KB have been divided into four additional blocks. The 16KB boot block can be used for a small initialization code to start the microprocessor, the two 8 KB parameter blocks can be used for parameter storage, and the remaining 32KB is a small main block where the application may be stored. CE#, OE#, and WE# signals control the bus operation. They enable simple connection to most microprocessors, often without additional logic. The device supplied with all the bits erased (set to 1).

供应链有货

IC 编号 数量 生产年份
M29W160ET-70N6E 5,760 2019+ 索取报价
M29W160ET-70N6E 524 索取报价
M29W160ET70N6F TR 1,682 202201 索取报价
M29W160ET-70N6F 1,405 16+ 索取报价
M29W160ET-70N6E 419 09+ 索取报价
M29W160ET-70N6E 1,389 182618+ 索取报价
M29W160ET-70N6E 4,032 索取报价
M29W160ET-70N6E 10,000 21+ 索取报价
M29W160ET-70N6E 5,760 索取报价
M29W160ET-70N6E 20,000 18+ 索取报价

可替代IC编号

IC 编号 脚位/封装 电压(伏) 速度 温度规格
S29AL016D70TFI013 TSOP-48 2.7V-3.6V 70 NS -40 C~+85 C

FFFE/互通料号 (形式,腳位和功能对等)

IC 编号 脚位/封装 电压(伏) 速度 温度规格
M29W160BT70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160CT-70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DT-70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DT-70N6 160ET TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DT-70N6/N1 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DT-70N61N1 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DT-70N6L TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DT-70N6T TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DT70N6T7 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160FT70N6T TSOP-48 3.3 V 70 NS -40 C~+85 C